09ee67f583
- create new files with code for demultiplexing the 4 switches from the one analog signal - define lookup table with measurements done with the build pcb, test switches and esp32 breakout board - add note do config that gpio used for digital in is now used for this multiplexer - main.cpp: disable control task, run new handle function in a loop for testing
85 lines
2.6 KiB
C++
85 lines
2.6 KiB
C++
#pragma once
|
|
extern "C" {
|
|
#include "driver/adc.h"
|
|
}
|
|
#include "gpio_evaluateSwitch.hpp"
|
|
#include "buzzer.hpp"
|
|
|
|
|
|
//===================================
|
|
//===== define output gpio pins =====
|
|
//===================================
|
|
//4x stepper mosfet outputs for VFD
|
|
#define GPIO_VFD_FWD GPIO_NUM_4 //ST4
|
|
#define GPIO_VFD_REV GPIO_NUM_16 //ST3
|
|
#define GPIO_VFD_D0 GPIO_NUM_2 //ST2
|
|
#define GPIO_VFD_D1 GPIO_NUM_15 //ST1
|
|
//#define GPIO_VFD_D2 GPIO_NUM_15 //ST1 (D2 only used with 7.5kw vfd)
|
|
|
|
#define GPIO_MOS2 GPIO_NUM_5 //mos2
|
|
#define GPIO_RELAY GPIO_NUM_13
|
|
#define GPIO_BUZZER GPIO_NUM_12
|
|
|
|
|
|
//==================================
|
|
//===== define input gpio pins =====
|
|
//==================================
|
|
#define GPIO_SW_START GPIO_NUM_26
|
|
#define GPIO_SW_RESET GPIO_NUM_25
|
|
#define GPIO_SW_SET GPIO_NUM_33
|
|
#define GPIO_SW_PRESET1 GPIO_NUM_32
|
|
#define GPIO_SW_PRESET2 GPIO_NUM_32 //gpio 34 currently used fir testing switches-analog
|
|
#define GPIO_SW_PRESET3 GPIO_NUM_39
|
|
|
|
#define GPIO_POTI GPIO_NUM_36
|
|
#define ADC_CHANNEL_POTI ADC1_CHANNEL_0
|
|
|
|
|
|
//--------------------------
|
|
//----- display config -----
|
|
//--------------------------
|
|
#if ESP_IDF_VERSION < ESP_IDF_VERSION_VAL(4, 0, 0)
|
|
#define HOST HSPI_HOST
|
|
#else
|
|
#define HOST SPI2_HOST
|
|
#endif
|
|
#define DISPLAY_PIN_NUM_MOSI GPIO_NUM_23
|
|
#define DISPLAY_PIN_NUM_CLK GPIO_NUM_22
|
|
#define DISPLAY_PIN_NUM_CS GPIO_NUM_27
|
|
#define DISPLAY_DELAY 2000
|
|
|
|
//--------------------------
|
|
//----- encoder config -----
|
|
//--------------------------
|
|
#define ROT_ENC_A_GPIO GPIO_NUM_19
|
|
#define ROT_ENC_B_GPIO GPIO_NUM_21
|
|
#define ENABLE_HALF_STEPS false // Set to true to enable tracking of rotary encoder at half step resolution
|
|
#define FLIP_DIRECTION false // Set to true to reverse the clockwise/counterclockwise sense
|
|
|
|
//--------------------------
|
|
//------ calibration -------
|
|
//--------------------------
|
|
//use encoder test for calibration and calculate STEPS_PER_METER
|
|
//#define ENCODER_TEST //show encoder count instead of converted meters
|
|
#define STEPS_PER_METER 2127 //roll-v3-gummi-86.6mm - d=89.8mm
|
|
//#define MEASURING_ROLL_DIAMETER 86.6 //roll v3 large
|
|
//#define PI 3.14159265358979323846
|
|
|
|
|
|
|
|
//============================
|
|
//===== global variables =====
|
|
//============================
|
|
//create global evaluated switch objects
|
|
//--- inputs ---
|
|
//create objects for switches at bottom screw temerinals
|
|
extern gpio_evaluatedSwitch SW_START;
|
|
extern gpio_evaluatedSwitch SW_RESET;
|
|
extern gpio_evaluatedSwitch SW_SET;
|
|
extern gpio_evaluatedSwitch SW_PRESET1;
|
|
extern gpio_evaluatedSwitch SW_PRESET2;
|
|
extern gpio_evaluatedSwitch SW_PRESET3;
|
|
|
|
//create global buzzer object
|
|
extern buzzer_t buzzer;
|