f8b9e6c862
- Add waitForStop function to custom stepper driver - use that function in guide-stepper to ensure stepper actually was at max/min position before dir change
266 lines
8.1 KiB
C++
266 lines
8.1 KiB
C++
extern "C"
|
|
{
|
|
#include <stdio.h>
|
|
#include "freertos/FreeRTOS.h"
|
|
#include "freertos/task.h"
|
|
#include "esp_log.h"
|
|
#include "driver/adc.h"
|
|
}
|
|
|
|
#include "stepper.hpp"
|
|
#include "config.hpp"
|
|
#include "guide-stepper.hpp"
|
|
#include "encoder.hpp"
|
|
|
|
|
|
|
|
//---------------------
|
|
//--- configuration ---
|
|
//---------------------
|
|
//also see config.hpp
|
|
//for pin definition
|
|
|
|
#define STEPPER_TEST_TRAVEL 65 //mm
|
|
|
|
#define MIN_MM 0
|
|
#define MAX_MM 50
|
|
#define POS_MAX_STEPS MAX_MM * STEPPER_STEPS_PER_MM
|
|
#define POS_MIN_STEPS MIN_MM * STEPPER_STEPS_PER_MM
|
|
|
|
#define SPEED_MIN 2.0 //mm/s
|
|
#define SPEED_MAX 60.0 //mm/s
|
|
|
|
#define D_CABLE 6
|
|
#define D_REEL 160 //actual 170
|
|
#define PI 3.14159
|
|
|
|
|
|
//simulate encoder with reset button to test stepper ctl task
|
|
//note STEPPER_TEST has to be defined as well
|
|
//#define STEPPER_SIMULATE_ENCODER
|
|
|
|
//----------------------
|
|
//----- variables ------
|
|
//----------------------
|
|
static const char *TAG = "stepper-ctrl"; //tag for logging
|
|
|
|
static bool stepp_direction = true;
|
|
static uint32_t posNow = 0;
|
|
|
|
|
|
|
|
//----------------------
|
|
//----- functions ------
|
|
//----------------------
|
|
//move axis certain Steps (relative) between left and right or reverse when negative
|
|
void travelSteps(int stepsTarget){
|
|
//TODO simplify this function, one simple calculation of new position?
|
|
//with new custom driver no need to detect direction change
|
|
|
|
int stepsToGo, remaining;
|
|
|
|
stepsToGo = abs(stepsTarget);
|
|
if(stepsTarget < 0) stepp_direction = !stepp_direction; //invert direction in reverse mode
|
|
|
|
while (stepsToGo != 0){
|
|
//--- currently moving right ---
|
|
if (stepp_direction == true){ //currently moving right
|
|
remaining = POS_MAX_STEPS - posNow; //calc remaining distance fom current position to limit
|
|
if (stepsToGo > remaining){ //new distance will exceed limit
|
|
stepper_setTargetPosSteps(POS_MAX_STEPS); //move to limit
|
|
stepper_waitForStop(1000);
|
|
posNow = POS_MAX_STEPS;
|
|
stepp_direction = false; //change current direction for next iteration
|
|
stepsToGo = stepsToGo - remaining; //decrease target length by already traveled distance
|
|
ESP_LOGI(TAG, " --- moved to max -> change direction (L) --- \n ");
|
|
}
|
|
else { //target distance does not reach the limit
|
|
stepper_setTargetPosSteps(posNow + stepsToGo); //move by (remaining) distance to reach target length
|
|
ESP_LOGD(TAG, "moving to %d\n", posNow+stepsToGo);
|
|
posNow += stepsToGo;
|
|
stepsToGo = 0; //finished, reset target length (could as well exit loop/break)
|
|
}
|
|
}
|
|
|
|
//--- currently moving left ---
|
|
else {
|
|
remaining = posNow - POS_MIN_STEPS;
|
|
if (stepsToGo > remaining){
|
|
stepper_setTargetPosSteps(POS_MIN_STEPS);
|
|
stepper_waitForStop(1000);
|
|
posNow = POS_MIN_STEPS;
|
|
stepp_direction = true;
|
|
stepsToGo = stepsToGo - remaining;
|
|
ESP_LOGI(TAG, " --- moved to min -> change direction (R) --- \n ");
|
|
}
|
|
else {
|
|
stepper_setTargetPosSteps(posNow - stepsToGo); //when moving left the coordinate has to be decreased
|
|
ESP_LOGD(TAG, "moving to %d\n", posNow - stepsToGo);
|
|
posNow -= stepsToGo;
|
|
stepsToGo = 0;
|
|
}
|
|
}
|
|
}
|
|
if(stepsTarget < 0) stepp_direction = !stepp_direction; //undo inversion of stepp_direction after reverse mode is finished
|
|
return;
|
|
}
|
|
|
|
|
|
//move axis certain Mm (relative) between left and right or reverse when negative
|
|
void travelMm(int length){
|
|
travelSteps(length * STEPPER_STEPS_PER_MM);
|
|
}
|
|
|
|
|
|
//initialize/configure stepper instance
|
|
void init_stepper() {
|
|
//TODO unnecessary wrapper?
|
|
ESP_LOGW(TAG, "initializing stepper...");
|
|
stepper_init();
|
|
}
|
|
|
|
|
|
//function that updates speed value using ADC input and configured MIN/MAX
|
|
void updateSpeedFromAdc() {
|
|
int potiRead = gpio_readAdc(ADC_CHANNEL_POTI); //0-4095 GPIO34
|
|
double poti = potiRead/4095.0;
|
|
int speed = poti*(SPEED_MAX-SPEED_MIN) + SPEED_MIN;
|
|
stepper_setSpeed(speed);
|
|
ESP_LOGW(TAG, "poti: %d (%.2lf%%), set speed to: %d", potiRead, poti*100, speed);
|
|
}
|
|
|
|
|
|
|
|
//----------------------------
|
|
//---- TASK stepper-test -----
|
|
//----------------------------
|
|
#ifndef STEPPER_SIMULATE_ENCODER
|
|
void task_stepper_test(void *pvParameter)
|
|
{
|
|
stepper_init();
|
|
int state = 0;
|
|
while(1){
|
|
vTaskDelay(20 / portTICK_PERIOD_MS);
|
|
|
|
//------ handle switches ------
|
|
//run handle functions for all switches
|
|
SW_START.handle();
|
|
SW_RESET.handle();
|
|
SW_SET.handle();
|
|
SW_PRESET1.handle();
|
|
SW_PRESET2.handle();
|
|
SW_PRESET3.handle();
|
|
SW_CUT.handle();
|
|
SW_AUTO_CUT.handle();
|
|
|
|
//cycle through test commands with one button
|
|
if (SW_RESET.risingEdge) {
|
|
switch (state){
|
|
case 0:
|
|
stepper_setTargetPosMm(50);
|
|
//stepper_setTargetPosSteps(1000);
|
|
state++;
|
|
break;
|
|
case 1:
|
|
stepper_setTargetPosMm(80);
|
|
//stepper_setTargetPosSteps(100);
|
|
state++;
|
|
break;
|
|
case 2:
|
|
stepper_setTargetPosMm(20);
|
|
//stepper_setTargetPosSteps(100);
|
|
state++;
|
|
break;
|
|
case 3:
|
|
stepper_setTargetPosMm(60);
|
|
//stepper_setTargetPosSteps(2000);
|
|
state = 0;
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
// if (SW_PRESET1.risingEdge) {
|
|
// buzzer.beep(2, 300, 100);
|
|
// stepperSw_setTargetSteps(1000);
|
|
// }
|
|
// if (SW_PRESET2.risingEdge) {
|
|
// buzzer.beep(1, 500, 100);
|
|
// stepperSw_setTargetSteps(10000);
|
|
// }
|
|
// if (SW_PRESET3.risingEdge) {
|
|
// buzzer.beep(1, 100, 100);
|
|
// stepperSw_setTargetSteps(30000);
|
|
// }
|
|
}
|
|
#endif
|
|
|
|
|
|
|
|
//----------------------------
|
|
//----- TASK stepper-ctl -----
|
|
//----------------------------
|
|
#ifdef STEPPER_SIMULATE_ENCODER
|
|
void task_stepper_test(void *pvParameter)
|
|
#else
|
|
void task_stepper_ctl(void *pvParameter)
|
|
#endif
|
|
{
|
|
//variables
|
|
int encStepsNow = 0; //get curret steps of encoder
|
|
int encStepsPrev = 0; //steps at last check
|
|
int encStepsDelta = 0; //steps changed since last iteration
|
|
|
|
double cableLen = 0;
|
|
double travelStepsExact = 0; //steps axis has to travel
|
|
double travelStepsPartial = 0;
|
|
int travelStepsFull = 0;
|
|
double travelMm = 0;
|
|
double turns = 0;
|
|
|
|
float potiModifier;
|
|
|
|
init_stepper();
|
|
stepper_home(MAX_MM);
|
|
|
|
while(1){
|
|
#ifdef STEPPER_SIMULATE_ENCODER
|
|
//TESTING - simulate encoder using switch
|
|
SW_RESET.handle();
|
|
//note
|
|
if (SW_RESET.risingEdge) encStepsNow += 500;
|
|
#else
|
|
//get current length
|
|
encStepsNow = encoder_getSteps();
|
|
#endif
|
|
|
|
//calculate change
|
|
encStepsDelta = encStepsNow - encStepsPrev; //FIXME MAJOR BUG: when resetting encoder/length in control task, diff will be huge!
|
|
|
|
//read potentiometer and normalize (0-1) to get a variable for testing
|
|
potiModifier = (float) gpio_readAdc(ADC_CHANNEL_POTI) / 4095; //0-4095 -> 0-1
|
|
//ESP_LOGI(TAG, "current poti-modifier = %f", potiModifier);
|
|
|
|
//calculate steps to move
|
|
cableLen = (double)encStepsDelta * 1000 / ENCODER_STEPS_PER_METER;
|
|
turns = cableLen / (PI * D_REEL);
|
|
travelMm = turns * D_CABLE;
|
|
travelStepsExact = travelMm * STEPPER_STEPS_PER_MM + travelStepsPartial; //convert mm to steps and add not moved partial steps
|
|
travelStepsPartial = 0;
|
|
travelStepsFull = (int)travelStepsExact;
|
|
|
|
//move axis when ready to move at least 1 step
|
|
if (abs(travelStepsFull) > 1){
|
|
travelStepsPartial = fmod(travelStepsExact, 1); //save remaining partial steps to be added in the next iteration
|
|
ESP_LOGD(TAG, "cablelen=%.2lf, turns=%.2lf, travelMm=%.3lf, travelStepsExact: %.3lf, travelStepsFull=%d, partialStep=%.3lf", cableLen, turns, travelMm, travelStepsExact, travelStepsFull, travelStepsPartial);
|
|
ESP_LOGI(TAG, "MOVING %d steps", travelStepsFull);
|
|
travelSteps(travelStepsExact);
|
|
encStepsPrev = encStepsNow; //update previous length
|
|
}
|
|
else {
|
|
//TODO use encoder queue to only run this check at encoder event?
|
|
vTaskDelay(5);
|
|
}
|
|
vTaskDelay(5 / portTICK_PERIOD_MS);
|
|
}
|
|
}
|