( pcb2gcode 2.5.0 )
( Software-independent Gcode )

G94 ( Millimeters per minute feed rate. )
G21 ( Units == Millimeters. )

G90 ( Absolute coordinates. )
G00 S20000 ( RPM spindle speed. )
G64 P0.05000 ( set maximum deviation from commanded toolpath )
G01 F200.00000 ( Feedrate. )


G00 Z30.00000 (Retract to tool change height)
T1
M5      (Spindle stop.)
G04 P1.00000 (Wait for spindle to stop)
(MSG, Change tool bit to cutter diameter 1.00000mm)
M6      (Tool change.)
M0      (Temporary machine stop.)
M3 ( Spindle on clockwise. )
G04 P1.00000 (Wait for spindle to get up to speed)
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G00 Z2.60000 ( retract )

G00 X-0.52496 Y1.02500 ( rapid move to begin. )
G01 Z-0.47500 F60.00000 ( plunge. )
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G01 F200.00000
G01 X-0.52496 Y51.35850
G01 X-0.52496 Y53.35850
G01 X-0.52496 Y103.69201
G01 X-0.53459 Y103.78957
G01 X-0.56303 Y103.88337
G01 X-0.60924 Y103.96980
G01 X-0.67142 Y104.04557
G01 X-0.74718 Y104.10775
G01 X-0.83362 Y104.15395
G01 X-0.92742 Y104.18240
G01 X-1.02498 Y104.19203
G01 X-81.04099 Y104.19203
G01 X-83.04099 Y104.19203
G01 X-163.05699 Y104.19203
G01 X-163.15453 Y104.18240
G01 X-163.24833 Y104.15395
G01 X-163.33477 Y104.10775
G01 X-163.41054 Y104.04557
G01 X-163.47272 Y103.96980
G01 X-163.51892 Y103.88337
G01 X-163.54737 Y103.78957
G01 X-163.55699 Y103.69201
G01 X-163.55699 Y1.02500
G01 X-163.54737 Y0.92747
G01 X-163.51892 Y0.83366
G01 X-163.47272 Y0.74723
G01 X-163.41054 Y0.67146
G01 X-163.33477 Y0.60928
G01 X-163.24833 Y0.56308
G01 X-163.15453 Y0.53463
G01 X-163.05699 Y0.52500
G01 X-83.04099 Y0.52500
G01 X-81.04099 Y0.52500
G01 X-1.02498 Y0.52500
G01 X-0.92742 Y0.53463
G01 X-0.83362 Y0.56308
G01 X-0.74718 Y0.60928
G01 X-0.67142 Y0.67146
G01 X-0.60924 Y0.74723
G01 X-0.56303 Y0.83366
G01 X-0.53459 Y0.92747
G01 X-0.52496 Y1.02500
G01 Z-0.95000 F60.00000 ( plunge. )
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G01 F200.00000
G01 X-0.52496 Y51.35850
G00 Z-0.90000
G01 X-0.52496 Y53.35850
G01 Z-0.95000 F60.00000
G01 F200.00000
G01 X-0.52496 Y103.69201
G01 X-0.53459 Y103.78957
G01 X-0.56303 Y103.88337
G01 X-0.60924 Y103.96980
G01 X-0.67142 Y104.04557
G01 X-0.74718 Y104.10775
G01 X-0.83362 Y104.15395
G01 X-0.92742 Y104.18240
G01 X-1.02498 Y104.19203
G01 X-81.04099 Y104.19203
G00 Z-0.90000
G01 X-83.04099 Y104.19203
G01 Z-0.95000 F60.00000
G01 F200.00000
G01 X-163.05699 Y104.19203
G01 X-163.15453 Y104.18240
G01 X-163.24833 Y104.15395
G01 X-163.33477 Y104.10775
G01 X-163.41054 Y104.04557
G01 X-163.47272 Y103.96980
G01 X-163.51892 Y103.88337
G01 X-163.54737 Y103.78957
G01 X-163.55699 Y103.69201
G01 X-163.55699 Y1.02500
G01 X-163.54737 Y0.92747
G01 X-163.51892 Y0.83366
G01 X-163.47272 Y0.74723
G01 X-163.41054 Y0.67146
G01 X-163.33477 Y0.60928
G01 X-163.24833 Y0.56308
G01 X-163.15453 Y0.53463
G01 X-163.05699 Y0.52500
G01 X-83.04099 Y0.52500
G00 Z-0.90000
G01 X-81.04099 Y0.52500
G01 Z-0.95000 F60.00000
G01 F200.00000
G01 X-1.02498 Y0.52500
G01 X-0.92742 Y0.53463
G01 X-0.83362 Y0.56308
G01 X-0.74718 Y0.60928
G01 X-0.67142 Y0.67146
G01 X-0.60924 Y0.74723
G01 X-0.56303 Y0.83366
G01 X-0.53459 Y0.92747
G01 X-0.52496 Y1.02500
G01 Z-1.42500 F60.00000 ( plunge. )
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G01 F200.00000
G01 X-0.52496 Y51.35850
G00 Z-0.90000
G01 X-0.52496 Y53.35850
G01 Z-1.42500 F60.00000
G01 F200.00000
G01 X-0.52496 Y103.69201
G01 X-0.53459 Y103.78957
G01 X-0.56303 Y103.88337
G01 X-0.60924 Y103.96980
G01 X-0.67142 Y104.04557
G01 X-0.74718 Y104.10775
G01 X-0.83362 Y104.15395
G01 X-0.92742 Y104.18240
G01 X-1.02498 Y104.19203
G01 X-81.04099 Y104.19203
G00 Z-0.90000
G01 X-83.04099 Y104.19203
G01 Z-1.42500 F60.00000
G01 F200.00000
G01 X-163.05699 Y104.19203
G01 X-163.15453 Y104.18240
G01 X-163.24833 Y104.15395
G01 X-163.33477 Y104.10775
G01 X-163.41054 Y104.04557
G01 X-163.47272 Y103.96980
G01 X-163.51892 Y103.88337
G01 X-163.54737 Y103.78957
G01 X-163.55699 Y103.69201
G01 X-163.55699 Y1.02500
G01 X-163.54737 Y0.92747
G01 X-163.51892 Y0.83366
G01 X-163.47272 Y0.74723
G01 X-163.41054 Y0.67146
G01 X-163.33477 Y0.60928
G01 X-163.24833 Y0.56308
G01 X-163.15453 Y0.53463
G01 X-163.05699 Y0.52500
G01 X-83.04099 Y0.52500
G00 Z-0.90000
G01 X-81.04099 Y0.52500
G01 Z-1.42500 F60.00000
G01 F200.00000
G01 X-1.02498 Y0.52500
G01 X-0.92742 Y0.53463
G01 X-0.83362 Y0.56308
G01 X-0.74718 Y0.60928
G01 X-0.67142 Y0.67146
G01 X-0.60924 Y0.74723
G01 X-0.56303 Y0.83366
G01 X-0.53459 Y0.92747
G01 X-0.52496 Y1.02500
G01 Z-1.90000 F60.00000 ( plunge. )
G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G01 F200.00000
G01 X-0.52496 Y51.35850
G00 Z-0.90000
G01 X-0.52496 Y53.35850
G01 Z-1.90000 F60.00000
G01 F200.00000
G01 X-0.52496 Y103.69201
G01 X-0.53459 Y103.78957
G01 X-0.56303 Y103.88337
G01 X-0.60924 Y103.96980
G01 X-0.67142 Y104.04557
G01 X-0.74718 Y104.10775
G01 X-0.83362 Y104.15395
G01 X-0.92742 Y104.18240
G01 X-1.02498 Y104.19203
G01 X-81.04099 Y104.19203
G00 Z-0.90000
G01 X-83.04099 Y104.19203
G01 Z-1.90000 F60.00000
G01 F200.00000
G01 X-163.05699 Y104.19203
G01 X-163.15453 Y104.18240
G01 X-163.24833 Y104.15395
G01 X-163.33477 Y104.10775
G01 X-163.41054 Y104.04557
G01 X-163.47272 Y103.96980
G01 X-163.51892 Y103.88337
G01 X-163.54737 Y103.78957
G01 X-163.55699 Y103.69201
G01 X-163.55699 Y1.02500
G01 X-163.54737 Y0.92747
G01 X-163.51892 Y0.83366
G01 X-163.47272 Y0.74723
G01 X-163.41054 Y0.67146
G01 X-163.33477 Y0.60928
G01 X-163.24833 Y0.56308
G01 X-163.15453 Y0.53463
G01 X-163.05699 Y0.52500
G01 X-83.04099 Y0.52500
G00 Z-0.90000
G01 X-81.04099 Y0.52500
G01 Z-1.90000 F60.00000
G01 F200.00000
G01 X-1.02498 Y0.52500
G01 X-0.92742 Y0.53463
G01 X-0.83362 Y0.56308
G01 X-0.74718 Y0.60928
G01 X-0.67142 Y0.67146
G01 X-0.60924 Y0.74723
G01 X-0.56303 Y0.83366
G01 X-0.53459 Y0.92747
G01 X-0.52496 Y1.02500

G04 P0 ( dwell for no time -- G64 should not smooth over this point )
G00 Z30.000000 ( retract )

M5 ( Spindle off. )
G04 P1.000000
M9 ( Coolant off. )
M2 ( Program end. )