82 lines
2.2 KiB
Plaintext
82 lines
2.2 KiB
Plaintext
# === USAGE ===
|
|
# simply run pcb2gcode in terminal while being in this folder.
|
|
# pcb2gcode will use "millproject" in current folder for parameters by default
|
|
#
|
|
# === Notes ===
|
|
# web based gcode viewer:
|
|
# https://ncviewer.com/
|
|
|
|
|
|
# === CONFIG ===
|
|
# Configuration file generated by pcb2gcodeGUI version 0.1 on Wed Apr 6 15:40:16 2022
|
|
# stopped using gui and customized parameters manually since then...
|
|
back=../export/pi-interface-board_v1.0-B_Cu.gbr
|
|
front=../export/pi-interface-board_v1.0-F_Cu.gbr
|
|
outline=../export/pi-interface-board_v1.0-Edge_Cuts.gbr
|
|
#note: running for each drill file separately and merging the gcode manually (4 mounting holes are in a separate gerber file)
|
|
drill=../export/pi-interface-board_v1.0-PTH.drl
|
|
#drill=../export/pi-interface-board_v1.0-NPTH.drl
|
|
|
|
output-dir=./out
|
|
|
|
# Common options
|
|
metric=true
|
|
metricoutput=true
|
|
nog64=false
|
|
|
|
#set optimized to default value, because when it was set to 0 (disable) it caused crash (runs till ram full) for some reason, since adding text to center of pcb ==> set to default
|
|
optimise=0.00000254 #default
|
|
backtrack=0 #if default/undefined caused unwanted moves in copper without retracting, especially at letters (seen in gcode viewer) - thus disabled this feature
|
|
tile-x=1
|
|
tile-y=1
|
|
tolerance=0.0500
|
|
zchange=30.0000
|
|
zchange-absolute=false
|
|
zero-start=true
|
|
zsafe=2.6000 #head mounting screw=1.8 #3mm to be able to cross mounting screws
|
|
|
|
# Mill options
|
|
extra-passes=0
|
|
mill-feed=400 #default 600mm/min
|
|
mill-speed=20000
|
|
offset=0.400 #intentional bigger offset than necessary, using 0.4 there were almost no small strips beeing left over between insolation lines.
|
|
voronoi=false
|
|
zwork=-0.2000 #usin 60degree cutter resulted in ~0.42mm line
|
|
|
|
# Drill options
|
|
drill-feed=200
|
|
drill-side=back
|
|
drill-speed=20000
|
|
milldrill=false
|
|
#@#milldrill-diameter=3.0000
|
|
nog81=false
|
|
nog91-1=true
|
|
onedrill=false
|
|
zdrill=-1.900 #1.75 slightly too short
|
|
drills-available=0.8, 1, 1.2, 1.5, 2, 3
|
|
|
|
# Outline options
|
|
bridges=1.0000
|
|
bridgesnum=2
|
|
cut-feed=200
|
|
cut-infeed=0.5000
|
|
cut-side=back
|
|
cut-speed=10000
|
|
cut-vertfeed=60
|
|
cutter-diameter=1.0000
|
|
fill-outline=true
|
|
zbridges=-0.6000
|
|
zcut=-1.9000 #actual: 1.7
|
|
|
|
# Autoleveller options
|
|
al-back=false
|
|
al-front=false
|
|
al-probecode=G31
|
|
al-probefeed=100
|
|
al-probevar=2002
|
|
al-setzzero=G92 Z0
|
|
al-x=15.0000
|
|
al-y=15.0000
|
|
software=custom
|
|
|